Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
- Brake system
- Brakes
The general description
Diagnostics
The diagnostic table
- Check and adjustment
Стравливание air from brakes
Check of free height of the brake lever
Adjustment of the light switch of brakes
Check it is superfluous a pedal course
Check of a free wheeling of the brake lever
Check of level of a brake liquid
Check of a brake hose and highway
Check of the main cylinder
Check of a brake disk
Check brake колодки
Check of a brake boot
Check and adjustment of a lay brake
Washing of hydraulic system of brakes
Check of pressure of a liquid (if the car is equipped LSPV)
Check of work of the brake amplifier
Specifications - an inhaling twisting moment
Necessary materials for service
The special tool
Brake highway/hose the brake cylinder
Forward brakes
Lay and back brake
Antiblocking brake system (ABS)
Engines
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment
|
Check and adjustment
Стравливание air from brakes
|
|
The brake liquid is very dangerous to a paint. If the liquid has casually got on the painted surface, immediately erase a brake liquid and clear the painted surface. |
|
|
If the vehicle is equipped АБС, be convinced that the ignition switch is disconnected. |
Necessarily pit air from brake system as set forth below when the oil hydrodrive is disconnected Hydraulic highways of brake system consist of two separate contours, one for brakes of forward wheels, another for brakes of back wheels. Стравливание air it is necessary for a brake of the right and left forward wheel, a brake of the left back wheel and LSPV (if the car has no АБС), i.e. in 4 places (3 places for vehicles with АБС).
Without АБС
|
|
1 — 4-foreign connection / 2-foreign connection
2 — the main cylinder
3 — LSPV
4 — a support of the right brake
5 — a support of the left brake
6 — the cylinder of the right wheel
7 — the cylinder of the left wheel
8 — activator ABS
• — a point стравливания air
F — the forward party |
WITH АБС
|
|
1 — 4-foreign connection / 2-foreign connection
2 — the main cylinder
3 — LSPV
4 — a support of the right brake
5 — a support of the left brake
6 — the cylinder of the right wheel
7 — the cylinder of the left wheel
8 — activator ABS
• — a point стравливания air
F — the forward party |
|
|
Fill a tank of the main cylinder with a brake liquid and support its filled in at least half during time стравливания air.
|
|
Remove спускную a stopper of a safety valve (1).
|
Attach a vinyl tube (2) to спускной to a stopper of a safety valve of the brake cylinder, and insert other end into a vessel (3).
|
|
Press some times on the brake lever, and then, keeping the lever in the pressed condition, release спускную a safety valve stopper approximately on one third-half of turn.
|
|
|
When pressure of a liquid in the cylinder is lowered to a minimum, tighten a trigger stopper of a safety valve.
|
Repeat operation until in a hydraulic line there will be no air vials.
|
|
When vials will disappear, press and keep the brake lever and tighten a trigger stopper of a safety valve.
|
Inhaling twisting moment
Forward brake
Back brake
Trigger stopper of a safety valve of the wheel cylinder (a): 7.5 Н•м (0.75 kg th, 5.5 pounds on foot)
Trigger stopper of safety valve LSPV (if the car is equipped by it): 7.5 Н•м (0.75 kg th, 5.5 pounds on foot)
Then attach a trigger stopper of a safety valve.
|
|
After стравливания air, submit pressure of a liquid to the pipeline and check up, whether there is no leak.
|
Fill up liquid level in a tank to the specified level.
Check up the brake lever on "softness". If the lever "soft", repeat procedure стравливания air.
|
|
|
|