Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
- Engines
   - Mechanical part of engine G16
       The general description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Klapannyj backlash
         Filtering element of the air filter
         Cover of a head of cylinders
         The case throttle заслонок and an inlet collector
         Collector of the fulfilled gases
         Drive belt газораспределительного the mechanism and the tension device for a belt
         Маслосборник and a grid of the oil pump
         The oil pump
         Коромысло the valve, an axis коромысел and a cam-shaft
         Valves and head of the block of cylinders
       Piston rod, piston rings, rods and cylinders
      The special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
    Mechanical part of engine J20
    Engine cooling
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment






Маслосборник and a grid of the oil pump

Components

1 — маслосборник
2 — a grid of the oil pump
3 — a sealant
4 — a lining of a drain stopper
5 — a drain stopper
6 — the gauge of an angle of rotation коленвала

7 — a nut маслосборника
8 — a bolt маслосборника
9 — a bolt of the gauge of an angle of rotation коленвала
10 — a bolt of a grid of the oil pump
11 — a bolt of an arm of a grid of the oil pump


Put hermetic 99000-31250 on the interfaced surfaces маслосборника and the block of cylinders, having addressed to subsection Installation.
The rotating moment of an inhaling.
Not to use repeatedly.

Removal

 PERFORMANCE ORDER

    Lift a vehicle. Remove the case of forward differential (1) with differential (2), having addressed to Section Removal in the Head Forward differential.
1 — the case of forward differential
2 — differential
3 — маслосборник
    Disconnect муфту the gauge of an angle of rotation коленвала and remove the gauge of an angle of rotation коленвала, having turned off its bolt (if that is available). Merge engine oil, having opened a drain stopper (2).
1 — маслосборник
2 — a drain stopper
    Remove the bottom plate of the case муфты (cases of the hydrotransformer for А/Т) (1).

    Remove маслосборник (3) and then a grid of the oil pump (2).

1 — the block of cylinders
2 — a grid of the oil pump
3 — маслосборник

Cleaning

 PERFORMANCE ORDER

    Clear the interfaced surfaces маслосборника and the block of cylinders.
    Remove oil, old hermetic and a dust from the interfaced surfaces and inside маслосборника.
    Clear a grid of the oil pump.

Installation

 PERFORMANCE ORDER

    Put hermetic on the interfaced surface маслосборника continuously. "And": hermetic 99000-31250.
"And" — 2 mm (0.05 inches)
b — 3 mm (0.12 inches)
    Place new consolidation (2) in that place.
    Establish a grid of the oil pump (1) and маслосборник (3). At first twirl a grid bolt, and then an arm bolt by the specified rotating moment.
      The rotating moment of an inhaling:
        Bolt of a grid of the oil pump (): 11 Н•м (1.1 kg th, 8.0 pound on foot) Bolt of an arm of a grid of the oil pump (b): 11 Н•м (1.1 kg th, 8.0 pound on foot)
    After adjustment маслосборника to the block of cylinders, insert tightening bolts and start to tighten at the centre: turn a wrench outside, twisting on one bolt at a time.
    Fasten bolts and nuts to the specified rotating moment. The rotating moment of an inhaling: a bolt and a nut маслосборника () — 11 Н•м (1.1 kg th, 8.0 pound on foot).
    Insert a new lining and a drain stopper in маслосборник (1). Fasten a drain stopper to the specified rotating moment. The rotating moment of an inhaling: a drain stopper () — 50 Н•м (5.5 kg th, 36.5 pound on foot).
    Establish the bottom plate of the case муфты (hydrotransformer) (1).
    Establish the gauge of an angle of rotation коленвала (1) and connect it муфту. The rotating moment of an inhaling: a bolt of the gauge of an angle of rotation коленвала () — 10 Н•м (1.0 kg th, 7.5 pound on foot).
    Establish the case of forward differential with differential, having addressed to Section Installation in the Head Forward differential. Fill the case of forward differential трансмиссионным with oil, having addressed to Section Servicing in the Head Forward differential. Fill in the engine with engine oil, having addressed to Section Engine oil and the filter in the Head Maintenance service and greasing. Check up, whether leaks engine oil and трансмиссионное oil from outside each connection.