Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
- Engines
    Mechanical part of engine G16
    Mechanical part of engine J20
   - Engine cooling
       The general description
       Diagnostics
      - Maintenance service
         Check of level of a cooling liquid
         Service and repair of system of cooling
         Washing and filling of system of cooling
         Regulation and check of a tension of a belt of the cooling fan
       Vehicle routine maintenance
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment





Regulation and check of a tension of a belt of the cooling fan

Disconnect a negative cable from the accumulator before to check and regulate a belt tension.

For engines G16

 PERFORMANCE ORDER

  1. Check up a belt on presence of cracks, cuts, deformations, deterioration and cleanliness. If what not so, replace a belt.
  2. Check up a belt tension. The belt tension is considered correct when it caves in according to following technical requirements under the pressure of a thumb (about 10 kg or 22 pounds). A tension of a belt of the cooling fan (for models of engines G16) "and": 5 – 7 mm (0.20 – 0.28 inches) sag under the pressure of 10 kg (22 pounds).

At replacement of a belt on new adjust a tension of a belt to 5 – 6 mm (0.20 – 0.24 inches) (engine G16).

Engine G16

1 — 10 kg (22 pounds)
2 — an adjusting bolt
3 — шарнирный a bolt
  1. If a belt will pull too poorly or too strongly, adjust its tension, having displaced generator position.
  1. Twirl an adjusting bolt and шарнирный a generator bolt.
  2. Connect a negative cable (-) to the accumulator.

For engines J20

 PERFORMANCE ORDER

  1. Examine a belt about cracks, cuts, deformations, deterioration and cleanliness. If what not so, replace a belt.
  2. Check up a belt tension. The belt tension is considered normal when it sags according to following technical requirements under the pressure of a thumb (about 10 kg or 22 pounds). A tension of a belt of the cooling fan (for engines of model J20) "and": sags on 5 – 7 mm (0.20 – 0.27 inches) under weight/10 of kg (22 pounds).

At replacement of a belt on new, adjust a tension of a belt to 4 – 5 mm (0.16 – 0.20 inches).

Engine J20

1 — 10 kg (22 pounds)
2 — an adjusting bolt
3 — a pulley коленвала
4 — a fan pulley
5 — шарнирный a bolt
  1. If a belt will pull too hardly or too poorly, adjust it as follows:
    • Ослабьте an adjusting bolt (1) and шарнирный a bolt (2).
    • Twirl an adjusting bolt (1), keeping at this time a fan belt in a corresponding tension, twisting высоконапряженный a bolt with the control of loading (3) wrench.
    • Fasten an adjusting bolt (1) and шарнирный a bolt (2) with the specified rotating moment.
  • The rotating moment of an inhaling:
    • Adjusting bolt of a pulley of the cooling fan (for engine J20) (): 45 Н•м (4.5 kg th, 32.5 pound on foot)
    • шарнирный a bolt of a pulley of the cooling fan (for engine J20) (b): 45 Н•м (4.5 kg th, 32.5 pound on foot)