Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
Engines
- Fuel system
- Current maintenance service of a vehicle
The fuel pump
The fuel filter
Fuel wires
Cover of a jellied fuel mouth
Fuel tank
Technical characteristics of the rotating moment of an inhaling
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment
|
Fuel tank
Removal
|
|
Dump pressure of fuel in striking топливопроводе.
|
|
This work cannot be made, if the engine hot. If it to make, it can negatively affect the catalyst. |
Disconnect a negative cable (-) from the accumulator.
|
|
Insert a fuel hose (1) manual pumps into a hose of a jellied mouth of a fuel tank and merge fuel in an interval "And" in drawing (to merge fuel through an interval until fuel will not cease to flow).
|
|
|
Do not insert a hose of the manual pump into a fuel tank. It you can damage the inlet (lock) valve (2). |
Remove a protector of a hose of a jellied mouth of a fuel tank.
|
|
Disconnect a hose of a jellied mouth (3) from a fuel tank (1) and a hose сапуна (2) from a neck of a jellied mouth.
|
Remove the inlet valve of a fuel tank (4). Be cautious, do not damage the inlet valve at съеме.
Drain a fuel tank, having pumped out the pump fuel through a bulk mouth of a fuel tank. Use the manual pump to drain a fuel tank.
|
|
Never merge or do not store fuel in the open container because of possible ignition or explosion. |
Disconnect an inlet hose of a bulk mouth (3) from a bulk mouth of a fuel tank (1).
|
|
1 — a mouth of a fuel tank
2 — a final hose of a bulk mouth of a fuel tank
3 — an inlet hose |
|
|
Disconnect a steam fuel hose (1) and a return fuel hose (2) from pipes.
|
Remove a protector of a fuel tank from a vehicle.
|
|
Slowly lower a fuel tank, keeping it in horizontal position, and remove everyone муфту from the fuel pump (1) and the pressure gauge in a fuel tank (2).
|
|
|
Check
Having removed a fuel tank, check up hoses and the pipes connected to a fuel tank, on presence of leak, easing of connection, deterioration or damage. And also check up, whether leaks the fuel pump and level gauge linings. Visually examine a fuel tank on presence of leakings and damage. Replace any damaged or faulty details.
Installation
|
|
Establish knot of the fuel pump (2) and the valve отсечки fuel (15) on a fuel tank (1). Address to Section the Fuel pump in this Chapter.
Connect fuel hoses to a fuel tank (1), the valve отсечки fuel (15) and knot of the fuel pump (2). After connection reliably fix clips of hoses.
Insert the inlet valve (14) into a fuel tank (1). If it was deformed or damaged otherwise, replace it with the new.
Establish a fuel tank (1) by means of belts (10) fuel tanks, and then establish a protector (9) on a vehicle.
The rotating moment of an inhaling:
Bolt of a fuel tank (): 50 Н•м (5.0 kg th, 36.5 pound on foot)
Bolt of a protector of a fuel tank (): 50 Н•м (5.0 kg th, 36.5 pound on foot)
Connect a hose of a jellied mouth (13) to a fuel tank (1) and a hose сапуна (5) to a neck of a jellied mouth (11). Reliably fix their clips.
The rotating moment of an inhaling
Hose clip сапуна (b): 2.0 Н•м (0.2 kg th, 2.0 pound on foot)
Clip of a hose of a jellied mouth (): 4.0 Н•м (0.4 kg th, 3.0 pound on foot)
Establish a protector of a hose of a jellied mouth of a fuel tank.
|
|
Connect fuel парошланг (1) and a return fuel hose (2) to a fuel pipe and reliably fix their clips.
|
Connect an inlet hose of the fuel filter (3) to the fuel filter (1).
|
|
1 — the fuel filter
2 — a final hose of the fuel filter
3 — an inlet hose |
Connect муфту to knot of the fuel pump and the pressure gauge in a tank, accordingly.
Connect a negative cable (-) to the accumulator.
On termination of installation check up, whether the fuel system leaks.
|
|
Procedure of a purge of a fuel tank
|
|
This procedure of a purge will not remove all fuel steams. Do not try to make the repair of a tank demanding application of fire or a flame as there can be an explosion conducting to a personal traumatism. |
The following procedure is used for a purge of a fuel tank.
|
|
Having removed a fuel tank, disconnect all hoses and knot of the fuel pump from a fuel tank.
Merge all rests of fuel from a tank.
Carry a tank in a washing zone.
Fill a tank with warm water or water from under the crane, well shake up and merge. Repeat this procedure обмыва until in a tank it is not becomes pure. Replace a tank, if it inside the rusty.
Completely pour out the rests of water after washing up.
|
|
|
|