Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
- Brake system
    Brakes
    Brake highway/hose the brake cylinder
   - Forward brakes
      - The general description
         Assemblage of a support of a brake disk
      Diagnostics
      Check and adjustment
       Vehicle service
      Inhaling twisting moment
      Necessary materials
    Lay and back brake
    Antiblocking brake system (ABS)
Engines
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment





Forward brakes

The general description

Assemblage of a support of a brake disk

All fastenings of a brake are the important elements of fastening and can affect work of the vital parts and systems, and-or much more to increase repair cost. It is necessary to replace them with details having the same number or equivalent if such replacement is necessary. Do not use for replacement of a detail of the worst quality or substitutes. It is necessary to observe the specified values of a twisting moment of an inhaling at assemblage to provide long service life of all details. It is not necessary to use welding as it can lead to extensive damages and metal easing.

This support is established on the holder of a support of a brake by two bolts of a support. The hydraulic effort created by pressing the brake lever, is transformed by a support to a friction. The hydraulic effort equally influences the piston and the bottom part of the channel of a support to submit the piston outside, and the support inside that leads to disk blocking/clip. The effort of a clip presses brake overlays to a disk, creating necessary pressure to stop a vehicle.

    Grease parts as it is specified. Do not use industrial compressed air for greasing of parts of brake system as it can damage rubber parts. If you remove any components or disconnect highways, pit air from brake system. Replace колодки only with complete sets. Values of a twisting moment of an inhaling are specified for the dry, not greased fastenings.
  • For definition of type of a support of a brake, the name of the manufacturer or an inscription see a brake support.

Manufacture TOKICO

1 — a bolt of the holder of a brake
2 — колодка
3 — a support of a brake disk (the cylinder of a brake disk)
4 — piston consolidation
5 — the piston of a brake disk
6 — колодка the cylinder
7 — internal колодка a brake disk
8 — external колодка a brake disk
9 — the holder of a support of a brake
10 — a spring колодки

11 — a stopper of a latch of a safety valve
12 — a cover of a stopper of a safety valve
13 — a bolt of a pin of a sled of a support (M12)
14 — a soundproofing lining
15 — an internal lining
16 — a bolt of a pin of a support (M10)
17 — a sleeve of a sled of a support
18 — a support pin
19 — a bolt of a pin of a support

Manufacture SUMITOMO ELECTRIC

1 — a bolt of the holder of a brake
2 — колодка
3 — a support of a brake disk (the cylinder of a brake disk)
4 — piston consolidation
5 — the piston of a brake disk
6 — колодка the cylinder
7 — internal колодка a brake disk
8 — external колодка a brake disk
9 — the holder of a support of a brake
10 — a spring колодки

11 — a stopper of a latch of a safety valve
12 — a cover of a stopper of a safety valve
13 — a bolt of a pin of a sled of a support (M12)
14 — a soundproofing lining
15 — an internal lining
16 — a bolt of a pin of a support (M10)
17 — a sleeve of a sled of a support
18 — a support pin
19 — a bolt of a pin of a support


Inhaling twisting moment.

Apply greasing to rubber.

Not иcпользовать repeatedly.