Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
Engines
Fuel system
Ignition system
Start system
Release system
- Transmissions
Mechanical transmission (type 1)
Mechanical transmission (type 2)
- Automatic transmission (4 A/T)
The general description
Diagnostics of an automatic transmission
Safety measures at diagnostics of malfunctions
- Visual survey
The basic check of automatic transmission
Tables of diagnostics of malfunctions
Check of the electroscheme of light
Codes of malfunctions
Check of linear pressure
Test in garage
Test for road
Manual test for road
Delay check
Check of a motor brake
Range check "P"
Service out of a workshop
System of blocking of brakes
System check
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment
|
Check of linear pressure
The purpose of this test is check of working conditions of each part by means of measurement of pressure of a liquid on a line of pressure of a liquid. Following conditions are necessary for performance of the test of linear pressure:
The liquid of an automatic box has normal working temperature (70-80 C/158 – 176F).
The liquid is filled to demanded level (between marks on щупе COMPLETELY HEATED-UP and "not HEATED-UP").
|
|
1 — an aperture for check of pressure of a liquid
2 — the pallet картера |
|
|
Reliably put on a lay brake and put to wheels the verifying device.
Attach the device for measurement of pressure of a liquid to an aperture for check of pressure of a liquid in the transmission case. The special tool (A): 09925-37810.
|
|
Having attached the device for check of pressure of a liquid, check up, that there was no liquid leak. |
|
|
1 — the pallet картера
2 — an exhaust pipe |
Press up to the end a brake pedal, include idling of the engine and limiting, and then check up pressure of a liquid in position “D” or “R”.
|
|
Do not leave the engine to work on speed limit more than 5 seconds. |
|
|
Engine G16
|
Power setting
|
Linear pressure
|
|
Position “D”
|
Position “R”
|
|
On single speed
|
3.9 – 4.4 kg/sm2
55 – 63 psi (pound / sq. inch)
|
5.1 – 5.7 kg/sm2
73 – 81 psi
|
|
On speed limit
|
11.7 – 13.2 kg/sm2
166 – 188 psi
|
14.2 – 16.7 kg/sm2
202 – 237 psi
|
Engine J20
|
Power setting
|
Linear pressure
|
|
Position “D”
|
Position “R”
|
|
On single speed
|
3.8 – 4.3 kg/sm2
54 – 61 psi (pound / sq. inch)
|
5.3 – 5.9 kg/sm2
75 – 84 psi
|
|
On speed limit
|
9.7 – 11.2 kg/sm2
138 159 psi
|
12.9 – 15.5 kg/sm2
183 220 psi
|
Engine G16
|
Power setting
|
Linear pressure
|
|
Position “D”
|
Position “R”
|
|
On single speed
|
3.9 – 4.4 kg/sm2
55 – 63 psi (pound / sq. inch)
|
6.6 – 7.2 kg/sm2
94 – 102 psi
|
|
On speed limit
|
11.3 – 12.7 kg/sm2
161 – 181 psi
|
14.7 – 22.7 kg/sm2
209 – 323 psi
|
|
Results of check
|
The possible reason
|
|
Linear pressure above standard level in each position
|
* The faulty valve of a regulator
* The faulty valve of a throttle
* The cable of a throttle of an automatic transmission is not adjusted
|
|
Linear pressure below standard level in each position
|
* Faulty coupling of raising transfer
* The faulty oil pump
* The faulty valve of a throttle
* The faulty valve of a regulator
* The cable of a throttle of an automatic transmission is not adjusted
|
|
Linear pressure below standard level only in position “D”
|
* Leak of a liquid from direct coupling
* Faulty coupling of raising transfer
* Leak in a chain of pressure of a liquid in position “D”
|
|
Linear pressure below standard level only in position “R”
|
* Leak of a liquid from direct coupling
* Faulty coupling of raising transfer
* Leak of a liquid from a backing brake
* Leak in a chain of pressure of a liquid in position “R”
|
The moment of an inhaling of a stopper of the case of a transmission: 17 Н•м (1.7 kg th, 12.0 pounds-foots).
|
|