Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
- Suspension bracket
   - Forward suspension bracket
      The general description
       Diagnostics
      - Service out of a workshop
         The stabilizer of cross-section stability/plug
         Shock-absorber rack
         Cylindrical spring
         The terminator of a dynamic course of a suspension bracket / a rubber nest of a spring
         Wheel nave (including the wheel bearing)
         Sharnir/os rotations
         The suspension bracket/plug lever
    Back suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
Engines
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment





Cylindrical spring

Removal

 PERFORMANCE ORDER

  1. Lift the car that the forward suspension bracket freely hung.
  2. Remove wheels.
  1. Remove a flange of a drive of an axis of a shaft (at the all-wheel drive car).
  1. Remove a spring ring of a shaft of a forward drive (1) (at the all-wheel drive car).
  1. Remove bolts of a support of a disk brake and hang up a support on a wire hook (1).

Hang up the removed support of a disk brake on a wire hook that the brake hose was not bent and it was not overwound and it was not stretched. Do not press a brake pedal when are removed brake колодки.


  1. If there is a system of antiblocking of brakes (ABS), remove a bolt of the plug of a wire (2) and remove the gauge of speed of a forward wheel (1) from a pin.

  • Do not pull a wire when remove the gauge of speed of a forward wheel (1).
  • Do not damage a surface of the gauge of speed of a forward wheel (1) and track, that the dust has not got to its aperture for installation, a dirt, etc.

  1. Remove a brake disk.

If it is impossible to remove a disk hands, take advantage of 8-millimetric bolts.

  1. Remove a bar of the stabilizer of cross-section stability as it is described in the given Chapter in Section the Stabilizer of cross-section stability/plug, (point Removal).
  1. Disconnect a tip of steering draught from a rotary pin by means of a stripper.
  1. Jack prop up the bottom lever.
  1. Remove bolts скобы racks.
  1. Remove a nut of a hairpin with a spherical tip.
  1. By means of a stripper disconnect a rotary pin from a hairpin with a spherical tip.
  1. Lowering a jack, remove a rotary pin and a wheel nave.
  1. Remove a cylindrical spring (1).
Installation

 PERFORMANCE ORDER

  1. For installation of a cylindrical spring execute in return sequence of manipulation on its removal.

The top and bottom diameters of a cylindrical spring неодинаковы. The end with the big diameter put downwards, and the free end establish in a nest of a spring (1).


Bottom.
  1. At a tightening of all болтовых connections observe the specified values of the moment of an inhaling.
  2. As to a nut of a hairpin with a spherical tip, do not forget to insert шплинт and to bend it after a nut tightening.
  3. Tighten a nut of a tip of steering draught a hairpin with spherical tips upwards that the hairpin did not rotate.

For the all-wheel drive car

a. For a washer of a shaft of a forward drive and an external axis of a fist of a forward wheel use литиевую plastic greasing. “A”: cмазка 99000-25010.

For the all-wheel drive car

b. At installation of a cutting lock ring (1) on a drive shaft use болтовое an aperture in a drive shaft to pull out it and to turn in the big diameter (2) rings to the right.

For the all-wheel drive car

c. At installation of a flange of a drive of an axis of a shaft (1) on a wheel nave put hermetic on an adjoining surface of a flange of a drive of an axis of a shaft and tighten a bolt of a flange (2) to the specified value of the moment of an inhaling. “A”: hermetic 99000-31090. The inhaling moment: a bolt of a flange of an axis of a shaft (a): 50 Н•м (5.0 kg th, 36.5 pounds-foots).

  1. Check up, that no alien material has stuck to the gauge and a rotor. Establish the gauge of speed of a wheel (1) and the plug of its fastening.
    • The inhaling moment:
      • Bolt of the plug of fastening (a): 10 Н•м (1.0 kg th, 7.5 pounds-foots)
      • Bolt of the gauge of speed (b): 23 Н•м (2.3 kg th, 17.0 pounds-foots)

At installation of the gauge of speed of a forward wheel do not pull and do not overwind excessively connecting wires. Reliably attach a sealing ring to an internal wing.

  1. Check up, that there was no backlash between the gauge and a fist.