Before check carrying out, be convinced of the following:
The fuel tank is completely filled by fuel.
The vehicle is equipped by a spare tyre cover, the tool, a jack and the jack handle.
Establish a vehicle on equal to a floor and establish loading about 200 kg (441 pounds) (2) on a back part of the case so that the back shaft weighed 800 kg (1764 pounds). Weight of a back shaft L: 800 kg (1764 pounds).
Establish the special tool on a forward and back brake.
|
|
The special tool should be connected with сапуном a forward brake (from outside the driver) and a back brake. |
The special tool of a forward brake:
(A): 9956-02310
(B): 09952-46510 (the adaptation for a support of a brake of the car with brake SUMITOMO ELECTRIC)
(C): 55473-82030 (спускная the valve stopper стравливания air (1) is delivered as the spare part)
Back brake
(A): 09956-02310
(B): 09952-36310 (the adaptation for a valve stopper стравливания air with diameter of a carving 7 mm) or 09952-46510 (the adaptation for a valve stopper стравливания air with diameter of a carving 8 mm)
(C): 55473-82030 (спускная the valve stopper стравливания air is delivered as the spare part)
|
|
|
|
Instead of the adaptation for diameter of a carving of 10 mm (3) to the special tool (A) the special tool (B) is used. Therefore remove the adaptation with (A) and establish (B).
- For a vehicle with a support of brake TOKICO, use the adaptation included in the special tool (A).
- For definition of type of a support of a brake address to the Head Forward brakes.
|
|
|
|
Gradually press the brake lever, pressure of a liquid in a forward brake does not become such, as set forth below and then check up corresponding pressure of a back brake. It should correspond to the specification more low.
|
Pressure of a back brake with the enclosed loading 8000 кПа (80 kg/sm2, 1,138 psi) on a forward brake
|
Forward brake
|
Back brake
|
|
8,000 кПа 80 kg/sm2 1,138 psi
|
3-door or model with collapsible top
|
6,000 — 7,300 кПа
60 — 73 kg/cm2
853 — 1,038 psi
|
|
5-door
|
4,500 — 7,300 кПа
45 — 73 kg/cm2
640 — 1,038 psi
|
After that put pressure of 100 kg/sm2 on a forward brake and check up that pressure of a back brake corresponds to the specification more low.
|
Forward brake
|
Back brake
|
|
10,000 кПа 100 kg/cm2 1,422 psi
|
3-door or model with collapsible top
|
6,500 — 8,000 кПа
65 — 80 kg/sm2
924 — 1,138 psi
|
|
5-door
|
5,000 — 8,000 кПа
50 — 80 kg/sm2
711 — 1,138 psi
|
|
|
If pressure of a back brake does not correspond to the specification, adjust it having changed position of a rack (3) as follows.
If pressure of a back brake above specified, move a rack (3) in a direction a, and if more low, in a direction b.
Repeat steps 3 - 5 while pressure of a back brake will not correspond to the specification.
After adjustment, tighten a bolt with an inhaling twisting moment according to specified in the specification. An inhaling twisting moment: a bolt of rack LSPV (a): 23 Н•м (2.3 kg th, 17.0 pounds on foot).
|
|
|
Disconnect a brake highway (2) (connecting the second contour of the main cylinder and 4-foreign connection) from the main cylinder (1). Tighten заглушку (the special tool) the main cylinder. Press the brake lever. If pressure of a back brake 95 - 100 kg/sm2 when pressure of a forward brake of 100 kg/sm2, it means that forward failure-safe system works properly. The special tool: (A) — 09956-02210.
|
|
Forward brake
|
Back brake
|
|
10,000 кПа 100 kg/sm2 1,422 psi
|
9,500 — 10,000 кПа
95 — 100 kg/sm2
1,350 — 1,422 psi
|
On termination of check of pressure of a liquid, pit air from brake system and execute check of brakes.
|