Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
- Brake system
Brakes
Brake highway/hose the brake cylinder
Forward brakes
- Lay and back brake
The general description
- Diagnostics
Check and adjustment
Vehicle service
Cable of a lay brake
Brake drum
Brake колодка
The brake cylinder
Back plate of a brake
Antiblocking brake system (ABS)
Engines
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment
|
Brake колодка
|
|
If the overlay is worn out beyond the limit, replace a boot.
If one of brake overlays is worn out to a limit, it is necessary to replace all overlays simultaneously.
Thickness brake колодки "a":
The standard: 6.5 mm (0.24 inches)
Deterioration limit: 3.0 mm (0.12 inches)
|
|
Never polish an overlay with an emery paper. If to polish with its emery paper, rigid particles from an emery paper remain on an overlay and can damage a drum. When it is necessary to correct an overlay, replace it with the new. |
|
|
Installation
|
|
The Note in the beginning of the given Chapter see. |
|
|
Before installation of a brake drum, check up external diameter brake колодки (3). If it does not correspond to the value resulted more low, adjust it according to specifications, having turned a regulator (4). External diameter brake колодки: "a" — 219.4 - 219.7 mm (8.638 - 8.650 inches).
|
|
1 — the lock lever
2 — a regulator pin |
Establish a brake drum, having convinced that an internal part of a brake drum and brake колодок are free from a dirt and oil.
On termination of works, press the brake lever with effort about 30 kg (66 pounds) from three to ten times to receive a necessary backlash between a drum and a boot. Adjust a cable of a lay brake (for adjustment, address to Section Check and adjustment of a lay brake in the Head Brake system).
Establish a back central console box.
|
|
Establish a wheel and tighten wheel nuts with the specified twisting moment of an inhaling. An inhaling twisting moment: a wheel nut (b): 100 Н•м (10.0 kg th, 72.5 pounds-foots). |
Check up and be convinced that a brake drum not заедает and brakes work correctly. Then remove a vehicle from the lift and execute brake check (a foot brake and a lay brake).
|
|
Brake колодка
Removal
|
|
Execute item 1 - 5 procedures of removal Has undressed the Brake drum.
|
|
Be especially cautious, establishing a returnable spring brake колодки. Wrong installation can lead to that the spring will come off and can become the trauma reason. |
|
|
Remove the springs pressing a boot (1), having unbent the pins pressing a boot (2).
|
Remove the top returnable spring (4), assemblage of a regulator (3), the lever of a regulator (5), a spring of the lever of a regulator (6), a spring of a rack (8), and сойку (7).
Remove brake колодки and the bottom returnable spring of a boot (9).
Remove brake колодки and disconnect a cable of a lay brake (2) from the lever колодки a lay brake (1).
|
|
3 — a branch pipe of a brake cable |
|
|
Remove the lever колодки a lay brake (2) and the holder (1) with brake колодки (3).
|
|
|
Survey
The lever of a lay boot
|
|
Examine the lever brake колодки and check up, whether movement concerning brake колодки is free. If it is faulty, correct or replace.
|
Regulator assemblage
|
|
Check up a carving or a ratchet of a rack and a regulator, whether there is no deterioration, jamming and corrosion.
|
Springs
|
|
Examine are not damaged and whether ослабли springs.
|
|
Examine each part with an arrow, whether there is no rust. If there are malfunctions, replace.
|
|
|
Brake колодка
Address to subsection Survey Has undressed the Brake drum.
Installation
|
|
Collect parts in an order, the return to an order at removal.
|
|
1 — the bottom returnable spring
2 — the bottom rack |
|
|
Establish the springs keeping a boot (1) having pressed down of them into place and turning clamping pins (2).
|
Establish assemblage of a regulator (3) and the top returnable spring of a boot (4).
Establish the lever of a regulator (5), a spring of the lever of a regulator (6), assemblage of a rack (7) and a spring of a rack (8).
Establish the bottom returnable spring of a boot (9).
Then address to Section the Brake drum.
|
|
|
|