Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
- Engines
   - Mechanical part of engine G16
       The general description
      - Routine maintenance
         Compression check
         Check of depression of the engine
         Check of pressure of oil
         Klapannyj backlash
         Filtering element of the air filter
         Cover of a head of cylinders
         The case throttle заслонок and an inlet collector
         Collector of the fulfilled gases
         Drive belt газораспределительного the mechanism and the tension device for a belt
         Маслосборник and a grid of the oil pump
         The oil pump
         Коромысло the valve, an axis коромысел and a cam-shaft
         Valves and head of the block of cylinders
       Piston rod, piston rings, rods and cylinders
      The special tool
      Necessary service materials
      Technical characteristics of the rotating moment of an inhaling
    Mechanical part of engine J20
    Engine cooling
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment






Collector of the fulfilled gases

Components

The car is not equipped warming three-componental каталитическим by neutralizer

1 — a collector of the fulfilled gases
2 — the top cover
3 — a lining
4 — the gauge of heating of oxygen-1
5 — the bottom cover

6 — an element of rigidity of a collector of the fulfilled gases
7 — the adaptation for engine lifting at dismantle
8 — муфта the gauge of heating of oxygen-2

The car is equipped warming three-componental каталитическим by neutralizer

1 — a collector of the fulfilled gases
2 — the top cover
3 — a lining
4 — the gauge of heating of oxygen-1
5 — the bottom cover

6 — an element of rigidity of a collector of the fulfilled gases
7 — the adaptation for engine lifting at dismantle
8 — муфта the gauge of heating of oxygen-2


The rotating moment of an inhaling.
Not to use repeatedly.

In order to avoid a burn, do not serve an exhaust system, if it still hot. Service should be spent after the system will be cooled.

Dismantle

 PERFORMANCE ORDER

    Disconnect a negative cable from the accumulator. Disconnect муфту the gauge of heating of oxygen-1. Remove the top cover of a collector of the fulfilled gases. Remove bolts or nuts of an exhaust pipe and a bolt of an arm of an exhaust pipe (if that is available).
1 — an exhaust pipe №1
    Remove an element of rigidity of a collector of the fulfilled gases (3) (if that is available).
    Remove a collector of the fulfilled gases (1) and its lining (2) from a cylinder head.

Installation

 PERFORMANCE ORDER

    Put a new lining (1) on a cylinder head.
    Establish a collector of the fulfilled gases and a rigidity element (if that is available).
    Attach condensing lining for connection of a pipe (1) and an exhaust pipe №1 (2) to a collector of the fulfilled gases (3). Before to establish condensing lining for connection of a pipe (1), check up it about damage or deterioration, and if necessary replace. Use new counternuts if they are worn out. Fasten pipe fixture to the specified rotating moment. The rotating moment of an inhaling: a bolt or a nut of an exhaust pipe №1 (): 50 Н•м (5.0 kg th, 36.5 pounds on foot).
    Establish the top cover on a collector of the fulfilled gases.
    Connect муфту the gauge of heating of oxygen-1 (1) and insert муфту into an arm (2), 3 adaptation for engine lifting at dismantle.
    Connect a negative cable to the accumulator. Check up, whether there is no leak of exhaust gas from an exhaust system.