Suzuka Grandee Vitara
The general information
Maintenance service and greasing
Heater, ventilation and the conditioner
Steering
Suspension bracket
Wheels and tyres
Forward приводной a shaft shaft/bearing. An oil epiploon
Kardannye shaft
Brake system
- Engines
- Mechanical part of engine G16
The general description
- Routine maintenance
Compression check
Check of depression of the engine
Check of pressure of oil
Klapannyj backlash
Filtering element of the air filter
Cover of a head of cylinders
The case throttle заслонок and an inlet collector
Collector of the fulfilled gases
Drive belt газораспределительного the mechanism and the tension device for a belt
Маслосборник and a grid of the oil pump
The oil pump
Коромысло the valve, an axis коромысел and a cam-shaft
Valves and head of the block of cylinders
Piston rod, piston rings, rods and cylinders
The special tool
Necessary service materials
Technical characteristics of the rotating moment of an inhaling
Mechanical part of engine J20
Engine cooling
Fuel system
Ignition system
Start system
Release system
Transmissions
Coupling
Transfer
Forward and back differentials
Windows, mirrors, locks and security measures. An immobilizer
Electric equipment
|
The case throttle заслонок and an inlet collector
Components
Dismantle
|
|
Dump fuel pressure.
Disconnect a negative cable from the accumulator.
Drain охладительную system.
|
|
|
|
In order to avoid a burn, do not open a stopper of a drain aperture and a radiator cover if the engine and a radiator have not cooled down yet. A burning liquid and steam can be pulled out outside under pressure if the stopper and a cover are opened too early. |
|
Remove воздухозаборный a sleeve.
|
|
Disconnect following electric wire conclusions:
The valve рециркуляции the fulfilled gases
Wires of grounding from an inlet collector
The gauge of absolute pressure of a collector
The gauge of temperature of a cooling liquid of the engine
Wire conclusions of injectors at муфты
The gate for release of not condensed gases
The gauge of position of the case throttle заслонок
The regulating pneumovalve
|
|
|
Disconnect a rope of an accelerator and a cable of a drive throttle заслонок А/Т (for models А/Т) from the case throttle заслонок.
|
Disconnect following hoses:
Brake sleeve from an inlet collector
Pneumohose from the gate for release of not condensed gases
Hose of a cooling liquid of the engine (the target party) from the case throttle заслонок
Entrance hose of a radiator from a thermostat cover
Hose of compulsory ventilation картера from an inlet collector and the case throttle заслонок
Hose of giving of fuel and returnable hose from each pipe
Vacuum hose from an inlet collector
|
|
Remove regulating shoulder of the generator.
|
Remove elements of rigidity of an inlet collector from an inlet collector.
|
|
Remove an inlet collector with the case throttle заслонок from a cylinder head, and then its lining.
|
|
|
Installation
|
|
Repeat dismantling procedure upside-down for the purpose of installation, without forgetting about the following.
|
|
Use a new lining for an inlet collector.
|
|
|
At installation of an inlet collector, establish clips in the positions specified in drawing.
|
|
|
Adjust люфт a rope of an accelerator and люфт a cable of a drive throttle заслонок А/Т (for models А/Т).
|
Check up, whether all removed parts are put into place. Repeatedly establish any necessary parts which have not been earlier established.
Back fill cooling system, having addressed to Section Washing and filling of system of cooling in the Head engine Cooling.
Adjust a tension приводного a belt of the water pump, having addressed to Section Regulation and check of a tension of a belt of the cooling fan in the Head engine Cooling.
On termination of installation turn the ignition key on ВКЛ, leaving the engine switched off, and check up fuel leak.
At last, include the engine and check up, whether engine antifreeze proceeds.
|
|
|
|